MAGNETO CUT OUT for Lucas MO1 MO1L N1 face cam magnetos

Vendido Ver artículos similares EUR 56,02 ¡Cómpralo ya!, Envío gratis, 14-Día Devoluciones, Garantía al cliente de eBay
Vendedor: themagnetoguys ✉️ (1.838) 98.3%, Ubicación del artículo: East Sussex, GB, Realiza envíos a: WORLDWIDE, Número de artículo: 282269891646 MAGNETO CUT OUT for Lucas MO1 MO1L N1 face cam magnetos.

POINTS CAP CUT OUT

(for Lucas face cam magnetos including MO1L and N1 models)

These magnetos do not have a facility for an ignition cut out – until now!

Following numerous enquiries from our customers over the years we have now developed a neat, reliable modification to enable a cut out to be fitted to your machine.

The system involves a new points cap modified to carry an insulated stainless steel stud which, in turn, houses a spring loaded carbon brush. The stud carries a ring terminal with approximately six feet of wire. The stud and electrical connection is then covered in a plastic cap with the whole arrangement held in place by a lengthened stainless steel points cap clip. Two lengths of points cap clip for MO1 magnetos are available dependent on where the clip is fitted. If it is fitted in the top left hand corner (as in the first picture), choose the short clip. The long clip is fitted in the top right hand corner. A third type of clip is available for N1 magnetos. PLEASE REMEMBER TO LET US KNOW WHICH TYPE OF CLIP YOU REQUIRE - OTHERWISE DELIVERY WILL BE DELAYED!

To fit, simply remove your old points cap and unscrew the old clip, screw the new clip into place and fit the new cut out cap. The wire can then be routed to wherever you choose to position your choice of new cut out switch (not supplied). Simple as that!

IMPORTANT: Please make sure that there is sufficient room for the increased depth of this modification - on some machines the magneto points cap is very close to the inside edge of the primary chain case. The plastic cap is 22mm in diameter and the depth of the plastic cap and clip is 17mm - please refer to picture showing dimensions. To keep the increased depth to a minimum, our new clips do not have the curled end as seen on the originals.

 

My bike has not had an ignition cut out for the last 40-50 years - why do I need one now?

There are several good reasons worth considering:

1: Use it to stop the engine safely: it’s true that the engine can be stopped by using the valve lifter and this works well when running at tick over. However, at higher revs there is a risk of causing damage to the valve lifter and/or the valve mechanism itself. What if the throttle sticks wide open?....... Run the cut out wire to a handlebar mounted push button switch. (Picture for illustration only - switch not included)

2: Use it to comply with racing regulations: an ignition cut out is a requirement in most forms of motorcycle competition. Run the cut out wire to the lanyard operated switch. (Picture for illustration only - switch not included)

3: Use it as a security device: most machines fitted with these magnetos had no security measures fitted as standard. Run the cut out wire to a hidden switch or perhaps a key operated ignition switch. (Picture for illustration only - switch not included)

4: Use it as a safety device: do you like to use an on/off tap in the oil line to prevent wet sumping? If the cut out wire is fed to a modified oil tap fitted with electrical contact points, it will prevent the engine being started without remembering to switch on the oil tap first. (Picture for illustration only - switch not included)

NOTE: When selecting a switch, choose one where the switch contacts are 'open' when in the 'running' position, 'closed' when in the 'stopped' position.

ONLY £48 with free P&P - no more to pay!

(and that applies to overseas customers too!)

REMEMBER: WHEN YOU BUY ONE OF THESE, PLEASE LET US KNOW IF YOU WANT THE MO1 LONG, THE MO1 SHORT OR THE N1 CLIP!

 

More questions? Please ask and I'll do my best to answer.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------

These are brand new units, designed and manufactured in the UK. Guaranteed for 12 months from date of purchase.

 

Yes, we repair and overhaul all types of magnetos and dynamos too - see our website for full details

www.themagnetoguys.co.uk

Any questions - please ask

-----------------------------------------------------------------------------------------------------------------

Trade with confidence - we intend to please!

Thanks for looking!

  • Condition: Nuevo
  • Brand: The Magneto Guys
  • Manufacturer Part Number: 2
  • Classic Motorcycle Part: Yes

PicClick Insights - MAGNETO CUT OUT for Lucas MO1 MO1L N1 face cam magnetos PicClick Exclusivo

  •  Popularidad - 1 seguidor, 0.0 nuevos seguidores por día, 30 days for sale on eBay. Cantidad normal en seguimiento. 1 vendidos, 3 disponibles.
  •  Mejor Precio -
  •  Vendedor - 1.838+ artículos vendidos. 1.7% votos negativos. Gran vendedor con la regeneración positiva muy buena y sobre 50 calificaciones.

La Gente También Amó PicClick Exclusivo