MakeSkyBlue MPPT Charge Controller When you choose the V118, then it's no wifi function. When you choose V119, then it's W ifi version and this Wifi is working for Android phone only . It does not work for Apple IOS system. V119=V118+WIFIBOX
Product Features: Intelligent Maximum Power Point Tracking technology Built-in DSP controller with high performance Automatic battery voltage detection 12V/24V/36V/48V Three-stage charging optimizes battery performance Multi-function LCD displays Overcharge protection Over temperature protection Easy to be mounted Suitable for battery types such as sealed lead acid, vented Gel, LiFePo4 and Lithium battery Notes: The output terminal is for DC only ( 12V system less 60W, 24V/36V/48V system less 100W ), and it will be burnt if connecting to other loads. The output for battery is no polarity reverse protection.
Datasheet
Special models for certain 72V or 96V Battery only
1. The advanced application for V118 30A, 40A, 50A and 60A:
If you want to control a big current load such as 100A, you could use the OU terminals to control it as below pictures.
(Figure 1):Using a relay to control a small current switch to achieve an inverter switching machine.
(Figure 2):Use relay to control high current load input circuit-loop.
2. The advanced application for V118 50A and 60A:
If your load device is shorted or over-current,
the controller will have output short-circuit protection and close the output.
When you disconnect the load and press ENT over 5 seconds,
then output will turn on again. Please note the 30A and 40A don't have this function.
3. The advanced application for V118 30A, 40A, 50A and 60A:
When the lithium battery is being charged,if the BMS protection board is turned off and the lithium battery is disconnected from the charging
circuit.The MPPT output to the battery voltage will not rise suddenly, and the controller doesn't cause the output voltage to overshoot
through the BMS protection board.By the way, the V118 version for 30A-60A can be set the charging voltage
from 12V to 17V and the fake products is from 13.5V to 17V.
Most frequently asked question 1. What information displays on the LCD? PV voltage / Output power Battery voltage / Charging current Working mode / Temperature Protection mode / ACC 2. How to choose lithium for solar controller? If Voltage from DC9V-DC15V, then as 12V styem. 24V/36V/48V as below. 12V system (DC9V-DC15V) 24V system (DC18V-DC29V) 36V system (DC30V-DC39V) 48V system (DC40V~DC60V) 3. Why there is no display when I connect the battery? Please choose right panels and battery, then connect all polarity correctly. Confirm your battery is over 12V, then the controller can boot up. 4. How to set the parameter for lithium? Following the manual, just set the D04 to 01, then set the charging voltage. 5. How to install the solar system if I don't have experience? Please ask the local solar engineer or contact us for help. 6. How to repair it after 1 or 2 years? Normally it works fine and if there is a problem, we'll provide spare parts for your repairing in order to use our controller as long as possible. 7. What's max wire size? You shall input 9awg / 6mm² for 30A and 40A. And input 2pcs 9awg / 6mm² for 50A and 60A. (Refer to the listing photo) 8. What's the difference between version V119 and V118? V119 has Wifi function and could monitor the parameter by Android phones.9. How to make these controllers in parallel?
For example, if you bought the 120A controller, then it's 2pcs 60A,
and you could connect them to each PV array to same battery directly and no need extra device or settings. 10. Where can I download the MakeSkyBlue MPPT V119 Controller APP? Please browse the offical website to download APP.Currently support Android phone only. 11. Will my old MSB controller work fine by mix verison V116/V117/ V118/V119 in parallel together ? Yes. 12. What does the meaning of D05 and D06? D05 Clear password for Wifi version only. D06 If you have accurate device and need to calibrate the battery voltage, then calibrate it by D06. Please be cautious to use this function.151. For example, if your accurate meter tests the battery and the voltage is 24.5V, but the controller battery voltage reads 24V , then use D06 to calibrate the voltage to 24.5V. Warranty One yearShipment We'll ship your items within 1 business day. All shipment with tracking code. We process and deliver the parcels from Monday to Saturday.
After-service and Feedback This is a very professional product and we recommend that you check and ask for more information about this device before placing your order. Send all clear photos (the LCD shows all information by code) and panel/battery details to us by email. The eBay message is unclear when any issues arise. |